Parasitic extraction

In electronic design automation, parasitic extraction is the calculation of the parasitic effects in both the designed devices and the required wiring interconnects of an electronic circuit: parasitic capacitances, parasitic resistances and parasitic inductances, commonly called parasitic devices, parasitic components, or simply parasitics.

The major purpose of parasitic extraction is to create an accurate analog model of the circuit, so that detailed simulations can emulate actual digital and analog circuit responses. Digital circuit responses are often used to populate databases for signal delay and loading calculation such as: timing analysis; power analysis; circuit simulation; and signal integrity analysis. Analog circuits are often run in detailed test benches to indicate if the extra extracted parasitics will still allow the designed circuit to function.

In early integrated circuits the impact of the wiring was negligible, and wires were not considered as electrical elements of the circuit. However below the 0.5-micrometre technology node resistance and capacitance of the interconnects started making a significant impact on circuit performance.^[1] With shrinking process technologies inductance effects of interconnects became important as well.

Major effects of interconnect parasitics include: signal delay, signal noise, IR drop (resistive component of voltage).

Interconnect capacitance is calculated by giving the extraction tool the following information: the top view layout of the design in the form of input polygons on a set of layers; a mapping to a set of devices and pins (from a Layout Versus Schematic run), and a cross sectional understanding of these layers. This information is used to create a set of layout wires that have added capacitors where the input polygons and cross sectional structure indicate. The output netlist contains the same set of input nets as the input design netlist and adds parasitic capacitor devices between these nets.

Interconnect resistance is calculated by giving the extraction tool the following information: the top view layout of the design in the form of input polygons on a set of layers; a mapping to a set of devices and pins (from a Layout Versus Schematic run), and a cross sectional understanding of these layers including the resistivity of the layers. This information is used to create a set of layout sub.wires that have added resistance between various sub-parts of the wires. The above Interconnect Capacitance is divided and shared amongst the sub-nodes in a proportional way. Note that unlike Interconnect Capacitance, Interconnect Resistance needs to add sub-nodes between the circuit elements to place these parasitic resistors. This can greatly increase the size of the extracted output netlist and can cause additional simulation problems.

This section is empty. You can help by adding to it. (July 2010)

The tools fall into the following broad categories.

• Field solvers provide physically accurate solutions. They calculate electromagnetic parameters by directly solving Maxwell's equations. Due to high calculation burden they are applicable only very small designs or to parts of the designs.
• Approximate solutions with pattern matching techniques are the only feasible approach to extract parasitics for complete modern integrated circuit designs.

ANSYS Q3D Extractor uses method of moments (integral equations) and FEMs to compute capacitive, conductance, inductance and resistance matrices. It uses the fast multipole method (FMM) to accelerate the solution of the integral equations. Outputs from the solver include current and voltage distributions, CG and RL matrices.^[2][3]

FastCap and FastHenry, from MIT, are two free parasitics extractor tools for capacitance, inductance, and resistance. Quoted in many scientific articles, they are considered golden references in their field.^{[citation needed]}

Source code and Windows binary versions with viewer and editor are freely available from FastFieldSolvers.^[4][5]

StarRC from Synopsys (previously from Avanti) is a universal parasitics extractor tool applicable for a full range of electronic designs.^[6]

Quantus from Cadence is a parasitic extractor tool for both digital and analog designs and parasitics extraction check have to be carried out to prepare the design for postlayout verification.^[7]

QuickCap NX from Synopsys is a parasitic extractor tool for both digital and analog designs.^[8] It was based on QuickCap developed by Ralph Iverson of Random Logic Corporation, which was acquired by Magma and Synopsys.

Calibre xACT3D from Mentor Graphics is a parasitic extractor tool for both digital and analog designs.^[9] It was based on PexRC developed by Wangqi Qiu and Weiping Shi of Pextra Corporation, which was acquired by Mentor.

• Standard Parasitic Exchange Format