|
155 mm gun T7
The 155mm L/40 T7 was an American rifled tank gun developed in 1945.[1] The T7 was to be the main armament for the T30 Heavy Tank, but only a handful were produced due to the T30 project being cancelled after trials in the late 1940s. The T7 used two-part separated ammunition like the 105mm T5E1 gun on the T29 Heavy Tank.[2] It had a low velocity of only 701 m/s (2,300 ft/s) compared to the 120mm T53 on the T34 Heavy Tank (945 m/s) and the 105mm T5E1 on the T29 Heavy Tank (945 m/s).[3] However, the 43 kg (95 lbs) High-Explosive shell (HE) and high-velocity armour-piercing (HVAP) was demonstrated to have a powerful demolition effect. Testing concluded before completion when the T30 project was cancelled in the late 1940s. AmmunitionPrevious developmentsDevelopment Document Approval of the design of the 155 mm T7 gun September 14, 1944 The 155 mm T7 L/40 (41.4 Caliber) is a 155 mm gun of the T30 heavy tank, developed from a shortened 155 mm M1 L/45 “Long Tom”, conceived as early as 14 September 1944. It was developed alongside with the T29 heavy tank armed with 105 mm T5E1 L/65 gun. The T30 had up to 5 different ammunition available for use. Starting from M107 HE, M110 WP, M112B1 APBC-HE, T29E1 APCBC-HE, and finally T35E1 APCR. The specification will be listed as fired from the T7. HE M107 155mm M107 HE Shell A standard high explosive shell used on all American 155 mm gun in WWII. Weighing 95 lb (43.09 kg), with an explosive filler of 15.13 lb (6.86 kg) TNT, this was primarily used as anti-fortification. It was also a default shell of the T30.
APBC-HE M112B1 155mm M112B1 APBC-HE Shell An armor-piercing round. Weighing 100.00 lb (45.36 kg), with an explosive filler of 1.44 lb (0.65 kg)) Explosive D, it was used as an anti-concrete shell, or as an anti-tank in secondary tank destroyer role. The difference between M112 and M112B1 is the cap. Performance-wise, both are identical. V50 penetration table on various AP projectiles tested by the Americans from the Canadian AFV Technical Situation Report No. 34, showing some well-known shell in service during WWII, including the 90 mm T33, 155 mm T7 gun fired 100.00 lb (45.36 kg) AP M112B1 at 2,200 ft/s (670 m/s) can penetrate a homogeneous armor plate, at only 228 mm penetration from point blank against vertical armor
APCBC-HE T29E1 Documents T29E1 shells for 155mm T7 The ballistic limit given is 2,533 ft/s (772 m/s) against 203 mm at 30° from vertical, measuring the 30° point blank penetration from given ballistic limit results 200 mm. With APCBC slope multiplier against vertical armor, that would mean about 284 mm from point blank range, substantially higher compared to the M112B1
HVAP-T T30 The 155 mm T35 HVAP, and 90 mm M304 for scale This was the largest APCR projectile to be developed for a tank gun in WWII. Designated as Shot, H.V.A.P., 155MM, T35E1, or just simply called as T35E1 HVAP. Grown out of the concern from encountering enemy heavily armored tanks, the U.S. Army Ground Forces was pressed to develop a necessary anti-tank munition for their latest heavy tank in development, the T29 and T30. These tanks were intended to support allied forces with combined heavy armor and heavy firepower to defeat the most well-fortified enemy positions with different roles. The T29 would be used to combat other tanks with its 105 mm gun, and the T30 would be relegated for anti-fortification with its 155 mm gun. Leaving the T29 aside since it was built to confront hostile armor anyway, the T30was stuck with no self-defense munition to hit back should it come across opponents like King Tiger or Jagdtiger. To quote the Office Memorandum from the U.S. Office of Research and Development about the T30 Heavy Tank project (8 February 1945)
A new anti-tank munition was then developed and designated as the 155 mm HVAP T35. Apart from looking comically large for a subcaliber shot, structurally, its design was similar to the 90 mm M304 HVAP with multi-piece carrier construction, consisting of aluminium body fitted with a steel bourrelet ring, an aluminium windshield, and a steel base fitted with a copper driving band and trace. However, the most ridiculous of all was the amount of penetrating core inside it. a whopping 14.9 lb (6.8 kg)) worth of tungsten carbide was crammed inside the projectile, with an estimated core diameter of 60 mm. This had the same weight of a single full-bore 76 mm M79 AP shot, but instead of monobloc steel, it was much harder tungsten carbide. The total weight of the entire projectile including the penetrator was 57.18 lb (25.94 kg). Test firing would be done using the T7 gun firing at full charge with a muzzle velocity of 3,630 ft/s (1,110 m/s). Its penetration was quite high, 392 mm versus RHA at 0° from point-blank. Compared with the 105 mm T29E3 HVAP of the T29, capable of penetrating up to 379 mm of RHA from similar setup. Compare armor penetration values  In conclusion, the 155 mm T7 was a medium velocity demolition gun mainly purposed for bunker busting, But in a scenario where it was forced to engage heavily armored vehicles, the T35 Projectile hyper-velocity shot was created to provide an effective countermeasure. It probably costed a fortune for the Ordnance Department to develop though, and was highly inefficient production-wise by wasting that much tungsten carbide for a single 155 mm HVAP, which could’ve been used to create three more 76 mm HVAP instead). The T35E1 HVAP project was terminated along with the T30 Heavy Tank postwar, partly due to the manufacturing cost, and the end of hostilities in both Europe and Pacific.
M110 WP (Smoke) 155mm M110 Smoke For the T30 heavy tank Smoke shell, used to provide smoke screen with 15.58 lb (7.07 kg) of white phosphorous. The ballistics and configuration are similar as the M107 HE.
Penetration comparison_Projectile_and_Brass_Shell_Casing.jpg) 90mm Shell (left), 155mm Brass Shell Casing (center), 155mm T43 (Mod.) AP Projectile (right) and 20mm shell (bottom corner)
Variants
References
Bibliography
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
